"Pictured is the before battery compartment. All rusted and hopeless. Josh invented a perfect plan to weld a tray to the two sides that were not rusted. Worked perfect. Even an RV place commented on the great job he did. What looked like a hopeless cause, turned into solid craftmanship. I Just hope he's available and doesn't get too busy.."
"I recently availed the services of Diamond cut solutions for a custom welding project on my mailbox, and I couldn’t be happier with the outcome. From the very beginning, the team demonstrated exceptional professionalism and a deep understanding of their craft. They listened carefully to my requirements and offered creative solutions to bring my vision to life. The quality of workmanship is evident in the precision of the welds and the overall aesthetic of the mailbox,m.Not only did they complete the project on time, but they also provided valuable maintenance tips to ensure its longevity. I’m thoroughly impressed with their attention to detail, customer service, and the passion they put into their work. If you’re looking for top-notch welding services that exceed expectations, Diamond cut Solutions is the way to go. Highly recommended for anyone seeking a blend of creativity, quality, and professionalism."
"I am a remodeling contractor and was referred to a client to repair their existing wood fence, which was beyond repair. Northland fence was willing to work with my company as a sub contractor to do a full replacement fence for my client. I was very satisfied with the pricing, communication and service they provided and my client is extremely satisfied. I would recommend Northland Fence and plan to work with them again in the future."
"Dan came out within 5 days from first contact and provided an initial bid, he walked through my needs and issues with the current fence and gave some good recommendations on the project approach and repairs. There were 2 other bids on this project and Dan was not only competitive in his pricing he was significantly lower than one of the bids (they stated their schedule and how small the work was attributed to the inflated cost but they bid on the EXACT SAME scope and material). Topline was able to come out within 2 weeks of the initial bid as they accommodated the work in between larger projects (thank you Dan!). The work was wonderfully performed. The new gates are great and the extension was seamless! Thanks for the great work and such an immediate response!"
Welcome to Q Shop LLC! We offer welding, fabrication, and machining services to businesses as part of the supply chain. We also complete repairs and fabrication services for clients provided they are able to bring the item to our facility. We do not provide services at the customer's site. \nHowever, due to COVID19, we are limiting our services to business to business at this time.
"Mike was very responsive and communicated along the way. He even squeezed in my project of fixing my railing. The quality of work was excellent and the price was fair. I would recommend Mike for any welding job."
We offer a variety of welding services. We guarantee your satisfaction, and we won’t leave until the job is done right. We pride ourselves on the quality of work we provide, while delivering great customer service! Check out all the services we offer below and call -or- click to schedule an estimate today! \n
Metalcore Welding and Repair, LLC, is a full service welding company with over 7 years of experience. We are honest, loyal and provide the best customer satisfaction in town. We pay very close attention to detail and owner is always on site to ensure quality work. Call us for a free estimate!
While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.
Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.
Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.
Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).
Your typical household tools will not cut a metal pipe. To cut a metal pipe, you’d need more specialized tools like a pipe cutter or circular saw. Do not attempt to use these tools without taking proper safety precautions and wearing safety gear. It’s usually safer to let a pro cut a metal pipe, especially if you’re not confident in your skills with a heavy-duty saw.
The Rockford, MN homeowners’ guide to welding services
From average costs to expert advice, get all the answers you need to get your job done.
The cost to install a 240-volt outlet in Minneapolis, MN varies depending on the amperage and the home’s current wiring conditions. Use this guide to budget for your next project.
When you need help with a metal project and don’t have the expertise or the time, call an expert welder for your project. Here’s how to vet and hire a welder.
Find the right steel beam installation company for your project. Learn what questions to ask, qualifications to check, and how to ensure structural safety.
