Top-rated welders.

Get matched with top welders in Hollywood, MD

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Hollywood, MD?

Select your specific project to find the pro for you.

Find Welders in Hollywood

Avatar for Fxomni custom solutions
Fxomni custom solutions
4.8(
6
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomMetal Structure or Object - Weld or Cut+3 more

Serving Hollywood, MD and surrounding areas

"I had Mike fabricate a custom set of headers with a 3 inch exhaust for a Ford Hemi I put into a 69 Mustang. He also boxed the front cross member for easier access to the oil pan. I was so impressed with his attention to detail that I had him modify the fuel cell to accept AN 10 fittings to feed my 528 cubic inch hemi. I refer friends and family to Mike for fabrication projects on their street rods or race cars Thomas"TJ"Johnson..."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+44

Recommended by100%of homeowners
Marroquin Welding
5.0(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomMetal Structure or Object - Weld or Cut+3 more

Serving Hollywood, MD and surrounding areas

In business since 2010

Free estimates

"They installed 10 feet of metal railing with nice decorations.  I got 10 different quotes. Some were from Home Advisor. These guys seemed to know what they where doing and their price was really reasonable, so I hired them. Right after the visit to my house, they sent me a quote and I approved it. They had how long it would take for the fabrication and welding time, and they included a schedule for installation. They did it right in the time they quoted. I was very pleased with the job. I would recommend this company to friends and family members.  I will definitely use them again in the future."
Recommended by100%of homeowners
Avatar for Hammer and Nail Exteriors
Hammer and Nail Exteriors
4.5(
187
)
Metal Structure or Object - Create CustomSheet Metal and Ornamental Metal - FabricateSteel Beams (Custom) - Fabricate+1 more

Serving Hollywood, MD and surrounding areas

In business since 1958

Free estimates

Credit card accepted

"The installers did a very good job. The company appears to have gone out of business. There was corrective work which was required and the company was not around to honor its obligation to make it right. The manufacturer, Marvin, stepped in and corrected the installation issues."
Entry door installation
Infinity® from Marvin bow window installation
Installation of Marvin Patio Door
Rotted Siding Before
JamesHardie Siding After

+7

Recommended by91%of homeowners
Showing 1-10 of 40
Welding questions, answered by experts

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Sawing your hot tub into more manageable chunks so it can be lifted easily into a truck takes several hours. Generally, 2.5 hours for smaller hot tubs and around 4 hours for larger ones with the help of one to two people. If money isn't a concern and you want to skip the physical labor, you can hire a pro to get the job done.

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

The Hollywood, MD homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.