Top-rated metal fabricators and restorers.

Get matched with top metal fabricators and restorers in Cedar Bluffs, NE

Q: Do welders need to be licensed or certified?

• <div><p>Some states require welders to be licensed and certified, while others don&rsquo;t. However, it&rsquo;s always a good idea to hire a licensed welder, regardless of requirements in your area, especially if you need welding for structural components of your home or gas lines. Licensed welders have gone through training and testing to prove their skills, so they&rsquo;re less likely to make a mistake that could be detrimental to your home. Use Angi&rsquo;s <a href="https://www.angi.com/angi-license-check.htm">state licensing tool</a> to determine whether your potential hire has a welding license.</p></div>

Q: What’s the fastest way to remove rust from metal?

• <div><p>The fastest and easiest way to remove small rust spots from metal is to combine lemon juice and baking soda or borax. You can mix them to make a thick paste, apply the paste to your rusted areas, let it sit for a half hour, and then gently scrub the spots with a bristle brush or old toothbrush. Finally, wipe the area clean with a lightly damp rag.</p></div>

Q: What building materials are in Federal architecture?

• <div><p>The most idyllic building material that encapsulates the feel of Federal architecture is a brick facade, often with bricks alternating between long side and short side. Palladium and arched transom windows are also prevalent, as are flat, white window lintels. More ornate Federal architecture buildings also include columns on either side of the front door. More important than most of the finer details, though, is the symmetry from the exterior. On the interior, ornate plaster moldings and plaster ceiling medallions are indicative of the style.</p></div>

Q: What’s the difference between a welder and a metal fabricator?

• <div><p>Welding is the process of using extreme heat&mdash;and, sometimes, pressure&mdash;to attach two pieces of metal. In contrast, metal fabrication is a more involved process that can include welding, sheet metal work, bending, and other forms of metal manipulation. Metal fabrication is a large-scale project that may or may not involve welding, while welding is more often a step in larger fabrication projects.</p></div>

Q: What are the most common materials to use for hardscaping?

• <div><p>Common hardscaping materials include coated steel or iron, asphalt, stone, concrete, and brick. Coated steel or iron provide durability and style for fences and gates while asphalt is a wallet-friendly option for driveways. Stone brings timeless beauty to steps, patios, and walkways. Concrete pavers and slabs are cost-effective, though they require more upkeep than stone alternatives. For a classic, upscale look, brick works beautifully in walls, walkways, and patios. Each material brings its own charm, so pick what fits your budget, style, and functional needs.</p></div>

Enter your ZIP and get matched with up to 5 pros

Need a pro for your metal fabrication and restoration project in Cedar Bluffs, NE?

Select your specific project to find the pro for you.

Verified Reviews for Metal Fabrication And Restoration pros in Cedar Bluffs, NE

*The Angi rating for Metal Fabrication And Restoration companies in Cedar Bluffs, NE is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Metal Fabrication And Restoration needs.

*The HomeAdvisor rating for Metal Fabrication And Restoration companies in Cedar Bluffs, NE is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Metal Fabrication And Restoration needs.

Last update on November 17, 2025

Reviewed in February 2025
They did a good job on installing a small oak floor that we had put in the house to match the rest of our oak floor.
Dinsmore Flooring, Inc.
Request a quote
Reviewed in August 2024
Leaks all over need a tarp over 30 in garage Sure 1002 more rest roof
Davis and Reed Homes
Request a quote
Reviewed in May 2024
Brad is amazing. We returned to our home after being gone for an extended time and found that the pipes had developed several leaks. Brad came immediately and was able to replace two shut-off valves and then returned the next morning to replace the third. He then checked the rest of the house to...
B & M Plumbing, LC.
Request a quote
Reviewed in November 2021
Wonderful! It is beautiful! Very professional team. They worked around my schedule and cleaned up afterwards. Will definitely hire again for the rest of our bathroom remodel. Extremely satisfied customer!!
DreamMaker Bath & Kitchen of Omaha
Request a quote
Reviewed in July 2010
Had a limb fall. Saw inside of limb had rotted. Found carpenter ants. They cut rest of the bad limb off cleanly. They told me I needed to treat for the carpenter ants. I thought they'd probably do that, but apparently not. They also told me how to protect the open wound of the tree to...
Drefs Tree Service
Request a quote

Find Metal fabricators and restorers in Cedar Bluffs

Dicko Metal Fab

4.70(

)

•Approved Pro

Dicko Metal Fab

4.70(

)

•Approved Pro

Customers say: Quick response

Recommended by 93% of Angi customers

14 years of experience

Welcome to Dicko Metal Fab, the leading metal fabrication and welding specialist serving Dodge County and the surrounding areas! With over 15 years of experience in metal fabrication and welding, we look forward to earning your business. Call today for a free estimate! I do exterior handrails and banister only.

"Really easy to work with, great attitude and the work was exemplary. Will have them replace the other three sets of outdoor metal stairs. Couldnâ t be happier."

Richard H on June 2021

"Really easy to work with, great attitude and the work was exemplary. Will have them replace the other three sets of outdoor metal stairs. Couldnâ t be happier."

Richard H on June 2021

Get matched with top metal fabricators and restorers in Cedar Bluffs, NE

Enter your ZIP and get matched with up to 5 pros

Need a pro for your metal fabrication and restoration project in Cedar Bluffs, NE?

Handyman for Multiple Small Project Service

Metal Stairs and Railings Installation and Replacement

Carpentry Framing Repair

Verified Reviews for Metal Fabrication And Restoration pros in Cedar Bluffs, NE

Find Metal fabricators and restorers in Cedar Bluffs

Dicko Metal Fab

Dicko Metal Fab

Bam's home & auto service

Bam's home & auto service

Cornhusker Welding

Cornhusker Welding

Anderson Sheet Metal

Anderson Sheet Metal

Greenwood Welding and Fence

Greenwood Welding and Fence

Classic Iron Design, Inc.

Classic Iron Design, Inc.

Sperling Industries

Sperling Industries

Whitney Manufacturing, Inc

Whitney Manufacturing, Inc

Z'S HOME IMPROVEMENT/SEAMLESS

Z'S HOME IMPROVEMENT/SEAMLESS

KATELMAN ANTIQUES

KATELMAN ANTIQUES

The Cedar Bluffs, NE homeowners’ guide to metal fabrication and restoration services

How Much Does Sheet Metal Fabrication Cost? [2025 Data]

How Much Does a Wrought Iron Railing Cost? [2025 Data]

6 Metal Stairs Questions to Answer Before Installation

Find Metal fabrication and restoration Pros in other cities near youNot finding what you are looking for in Cedar Bluffs? Check surrounding areas for Metal fabricators and restorers.

Which Metal fabrication and restoration task are you tackling?Find Cedar Bluffs Metal fabrication and restoration services on Angi who specialize in any of these tasks

Find Pros for other jobs in Cedar BluffsIf your Metal fabrication and restoration services job is complete, use Angi to find quality Pros in Cedar Bluffs for any number of jobs.