Is LVL more affordable than steel I-beams?

• <div><p>Yes, an LVL beam is more affordable than the <a href="https://www.angi.com/articles/how-much-does-steel-i-beam-cost.htm">cost of a steel I-beam</a>, totaling between $50 and $200 per linear foot as opposed to the $100 to $400 per linear foot you’d pay for a steel I-beam. Not only is the wood material more affordable than steel, but it’s also more similar to traditional wooden beams and doesn’t require as much retrofitting to connect joists. </p></div>

Why should I pick steel for my new support beam?

• <div><p>You should pick steel for your new support beam for a few reasons. While steel is more expensive than other materials, such as laminated veneer lumber or glulam, it offers the following benefits:</p><ul><li><p>Fire-resistant</p></li><li><p>Unaffected by pests</p></li><li><p>Longer-lasting</p></li><li><p>Stronger against water damage (when galvanized against rust)</p></li></ul><p></p></div>

Get matched with top welders in Spring Grove, MN

Q: Why should I pick steel I-beams?

• <div><p>Steel I-beams are an increasingly popular choice for supporting a structure because they support a large amount of weight with a small profile and without the need for load-bearing walls or supports underneath. This allows for more open floor plans, which most people tend to prefer. They also resist fire, pests, and rot and last for the lifetime of your home.</p></div>

Q: What’s the difference between a lintel and a beam?

• <div><p>The difference between a lintel and a beam is what loads each is responsible for supporting. A lintel is a type of beam that is responsible only for supporting the load above an opening, such as a window or door, and transfers the weight to the side walls around an opening. A beam supports the slab and transfers the load to nearby columns, which then disperse the load to the ground.</p></div>

Q: Do welders need to be licensed or certified?

• <div><p>Some states require welders to be licensed and certified, while others don&rsquo;t. However, it&rsquo;s always a good idea to hire a licensed welder, regardless of requirements in your area, especially if you need welding for structural components of your home or gas lines. Licensed welders have gone through training and testing to prove their skills, so they&rsquo;re less likely to make a mistake that could be detrimental to your home. Use Angi&rsquo;s <a href="https://www.angi.com/angi-license-check.htm">state licensing tool</a> to determine whether your potential hire has a welding license.</p></div>

Enter your ZIP and get matched with up to 5 pros

Need a pro for your welding project in Spring Grove, MN?

Select your specific project to find the pro for you.

Get matched with top welders in Spring Grove, MN

Enter your ZIP and get matched with up to 5 pros

Need a pro for your welding project in Spring Grove, MN?

Handyman for Multiple Small Project Service

Faucets, Fixtures and Pipes Repair or Replace

Wood Fence Installation

Find Welders in Spring Grove

B+ Welding

B+ Welding

Northeast Iowa Metalworks

Northeast Iowa Metalworks

Lumberjack Construction

Lumberjack Construction

Pulver Towing & Recovery

Pulver Towing & Recovery

Gale Marine, LLC

Gale Marine, LLC

C&L Powder Coating, LLC

C&L Powder Coating, LLC

Brummer Performance

Brummer Performance

Pequot Auto Repair

Pequot Auto Repair

KB RV Services

KB RV Services

BOAT DOCK

BOAT DOCK

The Spring Grove, MN homeowners’ guide to welding services

How Much Does Welding Cost? [2025 Data]

Find Welding Pros in other cities near youNot finding what you are looking for in Spring Grove? Check surrounding areas for Welders.

Which Welding task are you tackling?Find Spring Grove Welding services on Angi who specialize in any of these tasks