Top-rated concrete cutting pros.

Get matched with top concrete cutting pros in Toccoa, GA

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Toccoa, GA?

Select your specific project to find the pro for you.

TRUSTED BY TOCCOA, GA HOMEOWNERS

  • Average homeowner rating star icon4.8
    Average homeowner rating
  • Verified reviews icon20
    Verified concrete cutting services reviews

Find Concrete cutting pros in Toccoa

Harry B
New to Angi
Concrete Flatwork - Repair & Resurface

Serving Toccoa, GA and surrounding areas

Approved

Reliable and detail-oriented contractor providing high-quality home repair and improvement services. I specialize in a wide range of tasks including general repairs, installations, maintenance, and small to medium renovation projects. My goal is to deliver dependable workmanship, clear communication, and honest service on every job, whether it’s a quick fix or a larger project.\n\nI take pride in treating every home with care and ensuring the work is done right the first time. Punctual, professional, and committed to customer satisfaction, I focus on practical solutions that keep your home in good shape!

Roof rot repair
Roof rot repair
Roof rot repair
Roof rot repair
Floors Sag or Shake
4.7(
129
)
Concrete Flatwork - Repair & Resurface

Serving Toccoa, GA and surrounding areas

In business since 1980

Free estimates

Credit card accepted

"Very well. The slight dip in the kitchen looks better and the doors trued up. The slight sag still in the kitchen floor is because of the sub floor plywood which I didn't want to get in to. They leveled the joist by shimming the tops of several cinder block posts and installing a pair permanent of steel posts under a section of joist the previous owner had cut in two."
Recommended by93%of homeowners
Avatar for Tony Bell's Concrete
Tony Bell's Concrete
4.9(
4
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For BusinessConcrete Flatwork - Repair & Resurface

Serving Toccoa, GA and surrounding areas

In business since 2021

Free estimates

Small jobs welcome

"Tony and his crew did an awesome job on my new garage slab and a joining driveway. I wanted a smooth finished floor in the garage and Tony made it level, square and like glass. The driveway was done with the same quality work including French drains due to the existing elevation. They left the surrounding job sight clean and on grade, all I had to do was a light rake and seed . Tony honored his very reasonable quote for the completed job. I highly recommend Tony Bell Concrete. Thank you guys... again, AWESOME JOB!!!"
SLAB
SIDE WALK AND SLAB
SIDEWALKS AND DRIVEWAYS
DRIVEWAY
SIDEWALKS AND DRIVEWAYS

+17

Response time2 hrs
Recommended by100%of homeowners
Avatar for AAA Basement Waterproofing
AAA Basement Waterproofing
4.8(
83
)
Concrete Flatwork - Repair & Resurface

Serving Toccoa, GA and surrounding areas

In business since 1995

Free estimates

Emergency services offered

"Overall, it was a good experience. AAA put down a vapor barrier and installed a Santa Fe dehumidifier with sump pump. The result is that we can now use the stand-up basement/crawlspace to store things under the house without ruining them. This is the part that you need to know. The installation was not without problems. First, they broke an A/C drain pipe, second, they cut a sprinkler controller wire while running a PVC pipe. Here's my take, accidents happen but how does the business respond to these issues? Well, Donna was very quick to send her team out to correct the problems and they even paid for the damage to the sprinkler system. To me, that's top notch customer service. Any business can make a mistake, but how they handle it is the mark of a good company. Every time I lift the roll door and go into the basement now, I'm amazed at how cool and fresh the air is down there. No more mildew and no more smell."
Full Interior Encap Sys
Full Interior Crawl Drainage Sys
Before Crawl Drainage System
Before Sub-Floor System
After Sub-Floor System

+5

Recommended by100%of homeowners
Showing 1-10 of 45
Concrete Cutting questions, answered by experts

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

The Toccoa, GA homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.