
Average costs of HVAC inspections vary based on house size, location, and type of HVAC system. Follow our easy guide to gauge your home’s HVAC inspection cost.
Furnace repair costs in Minneapolis, MN, are $289 on average. The final cost depends on the furnace type, which part needs repair, and labor rates in your area, so the final price will range from $115 to $463. Reach out to a local HVAC pro for an accurate estimate.
The type of repair you need and the type of furnace you have are the two most influential cost factors to consider.
Most homes in Minneapolis use gas furnaces for heating, which are more costly to repair than electric furnaces.
Consider scheduling ongoing maintenance while you’re thinking about your furnace because this can extend the life of your system and increase its efficiency.
The cost of living in Minneapolis is more than 16% higher than the national average, which means labor costs for furnace repair will also be higher than average.
Furnace repair costs in Minneapolis average $289, and most repairs total between $115 and $463. Your costs will depend mostly on the specific component you need repaired or replaced. Homeowners in Minneapolis should also budget for ongoing maintenance, which can drastically improve the life and efficiency of systems in colder climates like Minnesota’s.
The cost of furnace repair in Minneapolis, MN, can sit as low as $60 if you need something simple, like air filter replacement, but prices can climb as high as $1,223 if you have a more complex and expensive component that needs repair.
Regardless of their fuel source, furnaces are complex appliances that have a lot of moving parts. Some of those parts significantly influence furnace repair costs, while others are simpler and less costly to repair.
Here is the average furnace repair cost based on the part:
Furnace Part | Average Cost |
---|---|
Burners | $140–$410 |
Blower motor | $140–$1,800 |
Circuit board | $180–$550 |
Coils | $550–$1,800 |
Combustion chambers | $90–$550 |
Draft inducer motor | $180–$1,400 |
Flame sensor | $140–$230 |
Flue pipe | $360–$730 |
Furnace filter | $50–$150 |
Gas valve | $180–$550 |
Heat exchanger | $90–$1,400 |
Ignitor | $140–$460 |
Relay switch | $140–$270 |
Thermostat | $90–$550 |
Transformer | $90–$160 |
Natural gas furnaces are the most common heating option in Minneapolis since most homes have a natural gas connection, and gas provides plenty of heat for the relatively cold climate. Some of the most common issues with gas furnaces include problems with the ignitor, the blower motor, the circuit board, and the flame sensor.
A furnace requires regular maintenance in order to operate efficiently. Otherwise, dust and other debris can clog burners, the pilot light, and other parts, causing more wear and tear on the system.
A furnace inspection costs $80 to $100 on average, and you need to schedule an inspection at least once per year to keep your system running smoothly. An advanced inspection, which includes cleaning and a tuneup, costs $125 to $200.
Additional maintenance costs include filters and air duct cleanings. You need to replace the filters once every 90 days, which will cost $4 to $140 per year. Schedule duct cleanings every three to five years, and expect to spend $275 to $500 for the cost of cleaning air ducts.
The climate in Minneapolis is quite cold and involves long, frigid winters, so most homeowners will call on their furnaces constantly for months at a time. In colder climates, it’s always a good idea to schedule routine maintenance for your heating equipment, which can prevent breakdowns and improve your heating system’s efficiency. Budget for routine maintenance at least once a year in Minnesota, regardless of the type of furnace you have.
HVACs are one of the most complicated and essential systems in our homes. To avoid further damage or safety risks, always hire a certified HVAC specialist to repair or replace broken parts.
Furnace repairs cost $50 to $150 per hour for the labor, plus you’ll need to budget for the cost of parts. Small repairs may be billed at a $100 to $200 minimum rather than by the hour.
One of the quickest repairs is to replace a dirty filter, which only takes a few minutes and is easy to DIY. Some of the more difficult, time-consuming parts to repair include the blower motor, the draft inducer motor, coils, and the heat exchanger.
Hiring an HVAC pro in Minneapolis costs an average of between $115 and $260 for labor alone, which means labor accounts for between 40% and 90% of your total. Major furnace repairs in Minneapolis can bring labor costs up to $1,000 or more, especially if the broken component is challenging to access.
The cost of living in Minneapolis is 16.5% higher than the national average, so your labor costs will also be above average since they scale with the local cost of living.
More extensive repairs, like replacing the blower motor or heat exchanger in your furnace, might require mechanical permits. The minimum permit fee that the City of Minneapolis charges for HVAC work is $84.20. If you need a full furnace replacement, you’ll pay a higher fee of $216.60.
Furnace repairs won’t always increase your home value, but keeping your heating system in good working order can prevent decreases in your property value, especially since heating equipment is such a necessity in the cold climate in Minneapolis.
If you find that you need to replace your furnace, doing so will definitely improve your home value since buyers will get greater peace of mind from a brand-new furnace and will know that they won’t be on the hook for repairs or breakdowns soon after closing. On average, furnace replacement provides a return on investment (ROI) of 30%, but upgrading to a more efficient unit in a cold climate like the one in Minnesota could provide an even higher return.
Home is the most important place on earth, which is why Angi has helped more than 150 million homeowners transform their houses into homes they adore. To help homeowners with their next project, Angi provides readers with the most accurate cost data and upholds strict editorial standards. We survey real Angi customers about their project costs to develop the pricing data you see, so you can make the best decisions for you and your home. We pair this data with research from reputable sources, including the U.S. Bureau of Labor Statistics, academic journals, market studies, and interviews with industry experts—all to ensure our prices reflect real-world projects.
Want to help us improve our cost data? Send us a recent project quote to [email protected]. Quotes and personal information will not be shared publicly.
From average costs to expert advice, get all the answers you need to get your job done.
Average costs of HVAC inspections vary based on house size, location, and type of HVAC system. Follow our easy guide to gauge your home’s HVAC inspection cost.
A swamp cooler offers cool, moist air and costs less than an air conditioner. Learn about the costs of swamp coolers based on your home size and type of unit.
Gas furnace replacement costs depend on the type of furnace you want and installation fees. Our guide explains all the factors involved in a new furnace cost.
Discover the true ductless heat pump cost for your home. Learn about installation, factors affecting price, and ways to save in this comprehensive cost guide.
Wondering 'what tonnage of AC do I need?' Read our guide to learn about AC tonnage, finding the right tonnage for your home's cooling system, calculating the square footage of your home, and who to hire to calculate AC tonnage for you.
Discover heat exchanger replacement costs to learn about price factors, labor, and ways to save before hiring a pro or starting your project.