Top-rated well and pump technicians.

Get matched with top well and pump technicians in Sutton, VT

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Sutton, VT?

Select your specific project to find the pro for you.

Find Well and pump technicians in Sutton

Avatar for Green Mountain Basement Solutions LLC
Green Mountain Basement Solutions LLC
4.0(
30
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Sutton, VT and surrounding areas

In business since 2007

Free estimates

Emergency services offered

"When I first called, I was surprised at how quickly they returned my phone call to set up an estimate. He was able to come over the next evening to check out our basement. He was punctual and provided us information about what would need to be done. He stated that he would provide us with an estimate that evening. I waited, but the estimate never came. I called the following week to see the status of the estimate. They stated that they were busy, but I should have it by now and would email it ASAP. After a second week, I called again. They said they would get it to me again. After the third week, I called again and was told the same thing. I gave up at that point and contacted someone else, who will be fixing the basement tomorrow. It's been over a month now and never received an estimate for the work. I understand that it's a busy time of year, but was disappointed to never get the estimate and didn't feel like I should have to pester them for it.
"
Recommended by75%of homeowners
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Sutton, VT and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Wells and Pumps questions, answered by experts

If you have a small well or a particularly high water demand, it’s possible to overuse your well. How quickly a well replenishes depends on its water source. In this case, you may want to purchase a water storage tank that you can fill from the well in off-hours, or if you’re planning to build a new well and you expect a large water demand, you may want to build a deeper well to match your needs.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

If you notice any changes to the water coming from your well, consider that a sign to get a well inspection. For example, if the water is foul-smelling, bad-tasting, cloudy, or discolored, you should call a pro. It’s also a good idea to schedule an inspection if you observe a loss of water pressure, broken equipment, loss of well capacity, or other unusual signs.

Most well pump pressure switches have a factory setting of 30 to 50 PSI. There’s some flexibility with this if you’d like a lower or higher water pressure, but remember that it should sit 2 to 3 PSI above your well tank’s general pressure setting.

The inside of your pressure switch cover will usually indicate minimum and maximum settings—going below and above the numbers might damage your well pump.

Consider replacement if the pump is over 10 years old or has recurring, costly issues.

The Sutton, VT homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.