Top-rated welders.

Get matched with top welders in Atoka, OK

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Atoka, OK?

Select your specific project to find the pro for you.

Find Welders in Atoka

Shepherd's Welding
5.0(
1
)
Metal Structure or Object - Weld or CutMetal Structure or Object - Create CustomWrought Iron Fence - Repair or Weld+2 more

Serving Atoka, OK and surrounding areas

Approved

Free estimates

Emergency services offered

Small jobs welcome

"Jacob responded very quickly. I sent photos to him. His quote was 1/3 that of another Angi contractor quote. Once scheduled, he arrived on time and finished the job within a few hours. He explained the work before, during, and upon completion. Excellent work! I hope we don't need future fence repairs or welding but I'll call Jacob at Shepherds Welding if we do."
36 neighbors recently requested a quote
Buckin' A Welding
0.8(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomSheet Metal and Ornamental Metal - Fabricate+3 more

Serving Atoka, OK and surrounding areas

Approved

Recently relocated to Grayson County. We've been serving Texas and other states for 13 years in building ground up commercial buildings, additions, and renovations. We specialize in structural steel fabrication and erection, custom steel fabrication, gates and entryways. We were designing and building Barndominiums before people knew what they were. We do the job right or not at all. We guarantee our work, and we often takeover failing or abandoned projects and get the project completed. We've built and have tore down and rebuilt many very large churches. We've done a lot of historical renovations and dealt woth the historical regulations, etc. We've done a lot of work at The Grandscape in The Colony Tx. We worked on The Dallas Morning News, The Statler Hotel as well as many other hotels, high end retail and entertainment districts. \n We have worked and a General contractor holding responsibility for a project from conception to planning and development, through completion.

Decker Welding & Fab
New to Angi
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomMetal Structure or Object - Weld or Cut+1 more

Serving Atoka, OK and surrounding areas

In business since 2021

Free estimates

Credit card accepted

We take great pride in our experience, expertise, quality, and customer service that we provide to meet the consumer's needs. It is our mission to provide excellent workmanship and complete customer satisfaction, from the start to the completion of a project. In order to understand the needs and expectations of our customers, we take great care to work and communicate with every customer in a professional manner. Our reputation is based on service, safety, and quality, regardless of how large or small the job.

...
Showing 1-10 of 57
Welding questions, answered by experts

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Sawing your hot tub into more manageable chunks so it can be lifted easily into a truck takes several hours. Generally, 2.5 hours for smaller hot tubs and around 4 hours for larger ones with the help of one to two people. If money isn't a concern and you want to skip the physical labor, you can hire a pro to get the job done.

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

The Atoka, OK homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.