Top-rated woodworkers.

Get matched with top woodworkers in Poplar Bluff, MO

Enter your zip and get matched with up to 5 pros

Need a pro for your woodworking project in Poplar Bluff, MO?

Select your specific project to find the pro for you.

Find Woodworkers in Poplar Bluff

Wilkerson Unlimited LLC
4.8(
5
)
Carpentry Framing - RepairInterior Trim and Decorative Moldings - Install

Serving Poplar Bluff, MO and surrounding areas

Approved

In business since 2022

Free estimates

Offers commercial services

Garry Construction is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Recommended by100%of homeowners
Avatar for Sentri Homes
Sentri Homes
2.9(
46
)
Carpentry Framing - InstallCustom Cabinets - Build

Serving Poplar Bluff, MO and surrounding areas

Approved

In business since 2023

Free estimates

Emergency services offered

"Found Sentri on Angi. Jeanette and Violet were very pleasant and efficient in getting a contractor to me in the time frame needed. The contractor was excellent and the roof looks great! I would definitely work with them again if I had additional projects."
20 neighbors recently requested a quote
Avatar for N-Hance of Southeast Missouri
N-Hance of Southeast Missouri
5.0(
1
)
Custom Cabinets - Build

Serving Poplar Bluff, MO and surrounding areas

Approved

In business since 2022

Free estimates

Credit card accepted

N-Hance of Southeast Missouri is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business

Response time40 mins
Response rate100%
5 neighbors recently requested a quote
...
Showing 1-10 of 81
Woodworking questions, answered by experts

If you don’t have a coping saw, you can use an angle grinder to cope crown molding, but it takes a little more precision. Place your molding down on your workbench, angle the grinder at a 45-degree angle toward the molding, and back cut the wood. You’ll need to carefully angle your grinder to accommodate the curves in the wood, and aim to remove around 1 inch from the profile of the molding.

No, you do not usually tip a carpenter for their work. However, if you’ve been very happy with the level of service and quality of work, a 10% to 20% tip would likely be accepted with thanks. If you’re not sure, it can help to discuss the carpenter’s policy or preference for tipping before beginning the project.

Landscape timbers can last 10 to 20 years in the ground when installed correctly. Pressure-treated timbers will last longer than non-treated ones, as pressure treatment makes the wood more rot-resistant. Wood exposed to high moisture levels or extreme temperature and weather fluctuations may not last as long as wood in drier areas with more consistent weather.

You should avoid drilling or cutting into load-bearing beams because removing material will weaken it and increase the risk of structural damage or even collapse. If you do need to drill into a load-bearing beam, speak with a structural engineer first to discuss where it’s safest to drill and the width and depth of the bit that’s safe to use.

Yes, you can find ceiling joists using simple tools if a stud finder isn't available.

Using a hammer requires patience and a keen ear. Gently tap the ceiling in a grid pattern, listening for sound changes. A hollow sound indicates space between joists, while a solid, dull thud suggests a joist. Mark the location with a pencil and confirm by tapping from different angles.

Alternatively, you can use a nail, but this method will leave small holes. You'll feel increased resistance when the nail hits a joist. Mark the spot and repeat the process every 16 or 24 inches to map the joist locations. This method is considered less reliable than using a stud finder.

The Poplar Bluff, MO homeowners’ guide to woodworking services

From average costs to expert advice, get all the answers you need to get your job done.