Top-rated well and pump technicians.

Get matched with top well and pump technicians in Chaffee, MO

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Chaffee, MO?

Select your specific project to find the pro for you.

Find Well and pump technicians in Chaffee

Montgomery Plumbing & Pumps
5.0(
2
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Chaffee, MO and surrounding areas

In business since 2010

Credit card accepted

At Montgomery Plumbing & Pumps, we pride our company on reliability, great communication, integrity, and quality work. We strongly believe in giving our absolute best in all the work we perform. We are experts and will always keep you educated about the work process. We look forward to earning your business.

Recommended by100%of homeowners
Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,678
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Chaffee, MO and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Chaffee, MO and surrounding areas

In business since 1971

Credit card accepted

"Rather than fix the issue the first 2 calls, more refrigerant was pumped into the system. This cost me $75 for each call plus the cost of the refrigerant. The 3rd time, they fixed a valve and refilled the refrigerant and I am monitoring to see if this really fixed the problem. So I am out $225 for service calls fro the same problem and the cost of the refrigerant. I think they take this approach intentionally."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Keeler Water Well Services
New to Angi
Well Pump - Repair or Service

Serving Chaffee, MO and surrounding areas

In business since 1970

Free estimates

Offers commercial services

We pride our company on reliability, great communication, integrity, and quality work. We believe in giving our absolute best in all of our projects, no matter how big or small. You will find us to be competitively priced, with close attention to the details of each and every project. We are experts in our trade and will always keep you educated on your particular task or project. We look forward to earning your business, so please ask us for references.

Wells and Pumps questions, answered by experts

For the most part, choosing between 30/50 psi and 40/60 psi is based on your water-pressure preference. However, it can also depend a little bit on your house—if you have older plumbing, a lower water pressure can be easier on the pipes (and a bit more gentle on your well pump). 

The lower 30/50 pressure is usually enough for a single-story home, but you may want 40/60 if you have multiple stories, as the extra pressure helps water flow smoothly up to the second floor.

Normally, when your well pump turns on or off, you’ll hear a small click. This isn’t anything to worry about, but it can be a problem if it’s clicking continuously. This can indicate that the well pump is short cycling—the pump continuously turns on and off.

This can wear out the motor and provide uneven water flow. If this happens, you may need to get it looked at by a well pump professional to see if you need to repair the switch or pump.

Yes, a bigger well pump can increase water pressure—up to a point. If you currently have a well pump of 8 GPM, you might notice a pressure boost when you go up to 10 GPM. However, overshooting significantly (going up to 15 GPM for an 8 GPM home) can strain your well system and result in things like burst pipes that can decrease your water pressure and make for costly repairs.

DIY is not recommended due to safety and technical requirements. Hire professionals for accurate diagnosis and repair.

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

The Chaffee, MO homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.