American Sheet Metal Heating & AC

unknown

unknown

It could not have went any better, very up front and honest about what could happen. Checked it out and got the job done quickly. Would highly recommend to anyone.

I've had a previous experience with Steve and American Sheet Metal when he estimated the cost of moving a flue for some remodeling in our previous home.  I was extremely impressed because he told me that flue relocation was really not necessary, and I could save a lot of money.  In short, he talked himself out of a expensive job.
Because I was so impressed, I contacted American Sheet Metal to estimate the cost of installing a new HVAC system in a new large detached barn/garage we were building.  Steve arrived within a couple of days, provided an estimate that same day, and I accepted his proposal.
He obtained the appropriate AA Co. permits immediately and started the work within a couple of weeks, and he finished the duct work and setting of the indoor and outdoor units inn a couple of days.  He later returned when the electrical work in the structure was completed to finish the job and start up the units. Everything is perfect!
Because this is an "industrial-type" building, all the interior duct work is exposed, and he took great pains to make it look very neat.  In fact, he took a great deal of pride in making all the duct work fit and look nice because it is not hidden behind walls and ceiling like residential installations.  His work is like art. The system is highly efficient and heat and cools the building very quickly.  The duct work is tight, and there are no air leaks when the system is running.  It is a first-class installation.
I could not possibly recommend anyone more highly.  Steve is pleasant and friendly.  He communicates clearly and answers the phone 99% of the time, the first time you call.  If you're planning a new installation, they are the company to call.
I will use them for all my HVAC maintenance and service needs in the future.

Awesome service and attention to detail.  Very responsive and did excellent work.  Would highly recommend!

Steve Smith, owner of the company, replaced my H/VAC system about 7 years ago after I received an excellent recommendation from a neighbor.  At the time, his estimate was competitive, but slightly higher than other quotes. However, based on his professionalism, thoroughness, and the excellent recommendation I had received, I oppted to go with him. I could not have been more pleased with my decision! The work was completed as scheduled, efficiently, and with no disruption to me. I was totally thrilled with the entire experience, and still am!
I recently purchased a "discount" Preventive Maintenance service with another vendor; although I was experiencing no issues  with my H/Vac system. The service fee included one pound of freon, if needed.  The owner/ service technician told me near the end of the service that he had  put in an additional 1 1/2 lbs over the amount included and then charged me an additional $145.00. He said the system still needed  more to top it off, but did not want to add any more, since he had already put in almost half of the maximum freon capacity.. He informed me that it was most likely a leak in the coil (a rough cost of about $1400 to replace) with such a massive loss of freon. He suggested I schedule a service call in the spring, and have the system rechecked, unless it stopped working before then.
After some deliberation,  I contacted Steve Smith at American Sheet Metal, and explained the situation.  Steve responded very quickly, came out and did a thorough inspection. He found no problems with the system, and the freon was up to maximum level, although it had been over a month since the other vendor had stated the level was still below maximum capacity.when he completed the service. I was once again reminded of Steve's integrity, knowledgeability, and professionalism.  I have also been reminded of an important lesson: Don't confuse "discount" pricing with quality and value!I
Based on my experiences, I recommend this company without hesitation, for any H/VAC needs,and will make certain I follow my own advice in the future.
.
                                                    .  Rating: AAA+ in all categories!

Went above and beyond expectations. Completed work in a timely manner and was very professional. Would recommend this company without hesitation.

unknown

In this particular case, Steve recommended that the flue be left as is, so in effect, he saved me a considerable amount of money, that he could have made on this job.  He consulted with the general contractor on a remodeling job to come up with an alternative design that would not require relocating the flue, and greatly reduced the total cost of the project.
The fact that a business owner would actually recommend against a job that would have been quite lucrative for his company impressed me a great deal.  His honesty and integrity are to be admired.  For that reason alone, I will definitely use this company on future jobs.

The price was reasonable; it wasn't a crazy amount. They were helpful and efficient. They came out about an hour after I made the call so they were quick in their response time. They did a good solid job.

They were excellent excellent.  They were responsive, quick, and did all the work in about a day and a half.  They were also very neat and clean.

American Sheet Metal was able to come out just days after I called to give me an estimate on a new heat pump, both inside and outside units. They offered me several solutions, gave me the pros and cons of each and recommended the product they thought fit my needs best. In other words, they didn't try to  sell me the most expensive choice. I spoke with friends in the industry and they agreed that the choice recommended by ASM was the best option. They came to install the unit about 3 days later. The guys who came to install the unit were very professional and quick. They were careful to keep the house clean while coming in and out. The unit was install perfectly and has been operating great. My heating/cooling bills have went down tremendously!