Top-rated well and pump technicians.

Best well and pump technicians near Firebaugh, CA

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Firebaugh, CA?

Select your specific project to find the pro for you.

Top-Rated Well and pump technicians in Firebaugh - Updated Nov 2026

Avatar for Living Water Well Drilling
Living Water Well Drilling
4.6(
5
)
Well Pump - Repair or ServiceWell Pump - Install or Replace

Serving Firebaugh, CA and surrounding areas

Approved

In business since 2005

Free estimates

Emergency services offered

"Trustworthy and prompt. Great response, fixed my well problem which was a broken stem on a valve, installed a more convenient shutoff. Excellent customer service. Highly recommended!"
Response time1 day
17 neighbors recently requested a quote
Recommended by100%of homeowners
Larry Huggins Water Well Services
4.0(
2
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Firebaugh, CA and surrounding areas

In business since 2014

Free estimates

"Larry Huggins Water Well Services arrived on time for our appointment. The upgrade to the wiring for our irrigation pump was performed quickly and efficiently. We were given friendly advice and information about our system. We would hire this company again if we need the service."
Response time10 mins
Recommended by100%of homeowners
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Firebaugh, CA and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Wells and Pumps FAQs, answered by experts

Wells typically replenish at a rate of about five gallons per minute, but several variables can influence how quickly they refill. A deep well will take more time to replenish than a shallow one. The replenishment rate can be slowed by issues such as leaks, damage, a faulty well pump, or a clogged well screen. Other factors, such as the surrounding geology, regular precipitation, and proper maintenance, also affect the recovery rate.

A shallow-well pump can pull water up to 25 feet deep. A deep-well pump can pull water up to 90 feet deep. A deep-well submersible pump can pull water up to 300 feet deep. Make sure to consult a pro to find out how deep your well is and get the right pump for your needs.

A well pressure tank is located between the well and the well pump, and it stores your water under pressure so that the well pump can eventually do its job. The well pump is activated whenever you turn a faucet on—it pulls the water from the tank into your home. Both are vital parts of a complete well water system.

For the most part, choosing between 30/50 psi and 40/60 psi is based on your water-pressure preference. However, it can also depend a little bit on your house—if you have older plumbing, a lower water pressure can be easier on the pipes (and a bit more gentle on your well pump). 

The lower 30/50 pressure is usually enough for a single-story home, but you may want 40/60 if you have multiple stories, as the extra pressure helps water flow smoothly up to the second floor.

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

The Firebaugh, CA homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.